brazing filler metal
英 [ˈbreɪzɪŋ ˈfɪlə(r) ˈmetl]
美 [ˈbræzɪŋ ˈfɪlər ˈmetl]
钎料
双语例句
- Brazed Interface Microanalysis of Carbon-fiber Reinforced Composite Material and Titanium Alloy by Brazing Filler Metal Containing Ti Element
含Ti钎料钎焊碳纤维复合材料与钛合金的界面微观分析 - This kind of brazing filler metal had a good filling performance, at the same time, sound high-temperature strength and impact toughness can be obtained in the joint.
该钎料不仅具有较好的填缝能力，同时获得的钎缝接头具有良好的高温强度和抗冲击性能。 - This paper introduces the connection using the brazing technique, selects corresponding brazing filler metal and flux together with proper technology, and determines the techniques and measures.
介绍了采用钎焊的方法进行连接；选择了相应的钎料与钎剂；并确定了工艺及措施。 - The stainless steel wet with brazing filler metal, before brazing aluminum alloys, it is the essential thoroughly to get rid flux residua, the joints will crack once through period of time if not.
钎料润湿不锈钢后再次与铝合金施焊前，彻底干净去除钎剂残渣是十分必要的，否则日后接头会再次开裂。 - The results show that the microstructure of brazing filler metal is mostly solid solution phase.
结果表明，钎料区主要是固溶体组织； - The affects of alloy elements of tin and phosphorus on the brazing properties of low silver brazing filler metal
合金元素锡和磷对低银钎料钎焊性能的影响 - The interface structure of the brazing filler metal with Ni after its spreading was observed by backscattered electron images.
采用背散射电子相观察钎料与Ni润湿后的界面组织。 - Study on wettability of Ti-Zr-Ni-Cu amorphous brazing filler metal on Si_3N_4 ceramic
Ti-Zr-Ni-Cu非晶钎料在Si3N4陶瓷上的润湿性研究 - The results show that the Au-Ag-Si brazing filler metal series have a good wettability with Ni.
研究结果表明：Au-Ag-Si系钎料合金与Ni润湿性良好，随着钎焊温度的增加，铺展面积增加，浸润角减小； - In this paper, the firm and imperishable joint between steel base and diamond grain was realized by using high-frequency induction brazing with the powdered brazing filler metal of alloy Ni-Cr, and by properly controlling the brazing current and time.
采用高频感应钎焊的方法，用Ni-Cr合金粉末做钎料，适当的控制钎焊电流和钎焊时间，实现了金刚石与钢基体的牢固焊接。 - Microstructure and strength of SiC/ Nb joint with Cu based brazing filler metal
铜基钎料钎焊SiC/Nb的接头组织及强度 - In order to solve the problem that brazing filler metal power and flux bring for stainless steel-aluminum by high frequency induction brazing, the brazing grease is developed.
为了解决不锈钢-铝高频感应钎焊用的粉末状钎料、钎剂所存在的缺点，研制了膏状钎料。 - Composite brazing filler metal, which provided by adding super-alloys, carbon or ceramic particulates of certain volume ratio as wild phase to common brazing filler metal, was used to alleviated the welding residual stress.
为缓解钎焊接头的残余应力，人们提出了在普通钎料中加入一定体积比的作为增强相的各种形态的高温合金、碳纤维及陶瓷颗粒等形成复合钎料的方法。 - Properties of Vacuum Brazed si_3n_4/ steel joint using active brazing filler metal
活性钎料真空钎焊Si3N4/钢接头性能的研究 - Vacuum brazing technology of a type of ultrasonic cutting tool is introduced in this paper. The main contents are composed of brazing filler metal. brazing method and brazing procedure.
介绍了超声切割刀具的真空钎焊技术，主要内容包括钎焊材料、钎焊方法和钎焊工艺。 - Study of low silver containing brazing filler metal in ag-cu-sn system
Ag-Cu-Sn系低银钎料的研究 - The temperature field that influences the wetting and spreading behavior of brazing filler metal under the unsteady arc heating is simulated and studied.
对在直流钨极惰性气体保护（GTAW）电弧钎焊过程中电弧加热的非稳态条件下温度场对钎料铺展润湿的影响进行了模拟研究。 - Study on Preparation and Brazing Diamond Film of Active Coated Brazing Filler Metal
活性涂层钎料的制备及其钎焊金刚石膜的研究 - Regression Modeling and Experimental Analysis of the Multi-element Cu Base Medium Temperature Brazing Filler Metal Powder with Fine Grain
多元铜基中温微晶硬钎料的试验研究及回归模型 - Characteristic and present situation on research of composite brazing filler metal
复合钎料的特点及研究现状 - The brazing technics of the EGR cooler and corrosion resistance of the joint, with three brazing filler metal-copper, BNi-2, BNi-7 brazing 316L stainless steel, is discussed in this paper.
本文主要研究三种钎料-纯Cu、BNi-2和BNi-7钎焊316L不锈钢的钎焊工艺及钎焊接头的耐腐蚀能力。 - The present situation of brazing on brazing technology, filler metal and flux of aluminium and its alloys is described.
综述了近年来铝及铝合金钎焊在钎焊方法、钎料及钎剂三个方面的技术发展现状，分别介绍了它们各自的发展方向。 - Investigation of Cu-P-Sn brazing filler metal without silver element
无银铜磷锡钎料的研究 - Using technology of magnetron sputtering in vacuum, we prepared the active coated brazing filler metal: Ti was sputtered onto the Ag-Cu alloy foil under proper sputtering voltage, sputtering current and sputtering time.
活性涂层钎料是运用真空磁控溅射镀膜技术，在一定的溅射电压、溅射电流和溅射时间条件下，在Ag-Cu钎料箔片表面溅射活性元素Ti。 - The melting temperature and brazability of the basic component of low temperature aluminium-based brazing filler metal are obtained through the orthogonal test.
通过正交实验，获得了低温铝基硬钎料基体成分的熔化温度和钎焊工艺性的实验数据。 - CREAM SOLDER USED FOR SILLIER BASE FILLER METAL Application of RE in Phosphor-copper Brazing Filler Metal
铜基与银基钎料用膏状钎剂的研究稀土在磷铜钎料中的应用 - Active brazing filler metal Ag Cu Ti and Cu Ti were chosen to braze directly cerment and stainless steel.
选用活性钎料AgCuTi或CuTi对陶瓷与不锈钢进行直接钎接。